|
Continental's Healds offer highly economized productive weaving. We invest
our skill, experience of generations, care and the right machines for required
tooling for quality achievements. Continental's Flat Steel Healds
are manufactured on sophisticated single line production facility matching
ISO / ISI & BS standards are widely accepted.
Flat Steel Healds are manufactured from cold rolled High Carbon Bright
Polished, both edges rounded strips for Slider Heald Frames.
Simplex / Duplex type Flat Steel Healds: Nuovo-Duplex & Simplex types
are offered for low speed Shuttle OR Rapier Water jet Weaving Machine for
Optimum performance.
End Loops: Simplex/Duplex Heald with 10mm off center eye are
generally offered having Top & Bottom Loops Off-Set (Twist Open). Simplex/Duplex
Healds having center eye are generally having corrugated loops on one side
& flat loop on other side to prevent them from being placed up side down on
the Heald Frame.
Eyelet of Healds: Wide range of Heald Eye sizes / types placed at
center / 10mm off center can be offered. Extra care is taken for polishing,
de-burring & Edge rounding to Heald Eye providing smooth surface for
Optimum performance.
Rust protection: Our Flat Steel Healds are supplied duly bright zinc
plated OR Nichrome plated. 100% Rust Proof Stainless Steel Healds can be
offered for Water Jet & High Density weaves.
Repair Healds: Harden & tempered plates welded on both the Heald
ends are known as repair Healds. They are used for replacing broken Healds OR
missing ends by simply hooked to the Heald Carrying Bar on the Heald Frame
during working.
Automatic Drawing-In: Flat Steel Healds suitable for any type of
Automatic Drawing-In can be offered providing End loop with Bevel stamped below
the loop.
Selection of suitable Healds: Continental's Flat Steel Healds are available
in different strip width with suitable Eye sizes & types for any weaving
requirements. Our Automatic production line allows production of Flat Steel
Healds in the length of 241mm (9.5”) to 457mm (18”). But generally, made in
popular sizes as shown in the chart.
[if !supportEmptyParas] [endif]
|
Selection
n mm
|
Corresponding
Eyelet
n mm
|
Distance between
the End Loops
In mm (Heald Length)
|
Ma. Density per Cm.
And per Heddle Bar
|
Recommended for
Warp-Threads
|
|
Simplex
|
Duplex
|
Tex &
Finer
|
Nm. &
Finer
|
Ne &
finer
|
Den &
Finer
|
|
2 x 03
|
5.5 x 1.2
|
|
280
|
300
|
330
|
|
12
|
20
|
30
|
34
|
20
|
300
|
|
2.3 x 0.35
|
6 x
1.5
|
280
|
300
|
330
|
380
|
420
|
10
|
17
|
60
|
17
|
10
|
600
|
|
2.6 x 0.4
|
6.5 x 1.8
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 x 1.8
|
280
|
300
|
330
|
380
|
|
9
|
14
|
72
|
14
|
8
|
|
|
3 x 0.45
|
7 x 2
|
|
300
|
330
|
380
|
420
|
8
|
|
125
|
8
|
5
|
|
[if !supportEmptyParas] [endif]
Special Healds: Our 2-generation's experience in Heald
making made us capable to offer any odd requirements of special Healds as per
customer's requirements.
Our Other products -
Heald Frames, All Metal REED, Drop Pins, Electrical Contact Bars, Leno Doup
Healds, Ribbon/Needle Loom Healds, Wire Healds, kindly ask for the respective
catalogues or get in direct touch with us.
Odd is Even for
Continental's
Need is the mother of all inventions, we in Continental's do not see anything
impossible. We create the products for the knish market also & we can also
provide the tailor-made solutions for your
[if !supportEmptyParas] [endif]
|
