|
Continental's Healds offer highly economized productive weaving. We invest our skill, experience of generations, care and the right machines for required tooling for quality achievements. Continental's Flat Steel Healds are manufactured on sophisticated single line production facility matching ISO / ISI & BS standards are widely accepted. Flat Steel Healds are manufactured from cold rolled High Carbon Bright Polished, both edges rounded strips for Slider Heald Frames. Simplex / Duplex type Flat Steel Healds: Nuovo-Duplex & Simplex types are offered for low speed Shuttle OR Rapier Water jet Weaving Machine for Optimum performance. End Loops: Simplex/Duplex Heald with 10mm off center eye are generally offered having Top & Bottom Loops Off-Set (Twist Open). Simplex/Duplex Healds having center eye are generally having corrugated loops on one side & flat loop on other side to prevent them from being placed up side down on the Heald Frame. Eyelet of Healds: Wide range of Heald Eye sizes / types placed at center / 10mm off center can be offered. Extra care is taken for polishing, de-burring & Edge rounding to Heald Eye providing smooth surface for Optimum performance. Rust protection: Our Flat Steel Healds are supplied duly bright zinc plated OR Nichrome plated. 100% Rust Proof Stainless Steel Healds can be offered for Water Jet & High Density weaves. Repair Healds: Harden & tempered plates welded on both the Heald ends are known as repair Healds. They are used for replacing broken Healds OR missing ends by simply hooked to the Heald Carrying Bar on the Heald Frame during working. Automatic Drawing-In: Flat Steel Healds suitable for any type of Automatic Drawing-In can be offered providing End loop with Bevel stamped below the loop. Selection of suitable Healds: Continental's Flat Steel Healds are available in different strip width with suitable Eye sizes & types for any weaving requirements. Our Automatic production line allows production of Flat Steel Healds in the length of 241mm (9.5�) to 457mm (18�). But generally, made in popular sizes as shown in the chart. [if !supportEmptyParas] [endif]
|
Selection
n mm
|
Corresponding
Eyelet
n mm
|
Distance between
the End Loops
In mm (Heald Length)
|
Ma. Density per Cm.
And per Heddle Bar
|
Recommended for Warp-Threads
|
|
Simplex
|
Duplex
|
Tex &
Finer
|
Nm. &
Finer
|
Ne &
finer
|
Den &
Finer
|
|
2 x 03
|
5.5 x 1.2
|
|
280
|
300
|
330
|
|
12
|
20
|
30
|
34
|
20
|
300
|
|
2.3 x 0.35
|
6 x 1.5
|
280
|
300
|
330
|
380
|
420
|
10
|
17
|
60
|
17
|
10
|
600
|
|
2.6 x 0.4
|
6.5 x 1.8
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 x 1.8
|
280
|
300
|
330
|
380
|
|
9
|
14
|
72
|
14
|
8
|
|
|
3 x 0.45
|
7 x 2
|
|
300
|
330
|
380
|
420
|
8
|
|
125
|
8
|
5
|
|
[if !supportEmptyParas] [endif] Special Healds: Our 2-generation's experience in Heald making made us capable to offer any odd requirements of special Healds as per customer's requirements. Our Other products - Heald Frames, All Metal REED, Drop Pins, Electrical Contact Bars, Leno Doup Healds, Ribbon/Needle Loom Healds, Wire Healds, kindly ask for the respective catalogues or get in direct touch with us. Odd is Even for Continental's
Need is the mother of all inventions, we in Continental's do not see anything impossible. We create the products for the knish market also & we can also provide the tailor-made solutions for your [if !supportEmptyParas] [endif]
|
